Burst Disc # 1106

View Larger Image

Protect yourself in the event of burner failure, Pre set to open at 8,000 PSI.  NET PRICED

Hi Amp Relay- 40 Continuious # 1699

View Larger Image

40 Amps Continuous, 100 Amp Spike Protection. Most 12 V burner problems are caused by the heavy in rush of power (spike). This condition can reduce the life of 12 Volt motors and Igniters by 80%. These relays will cushion the electrical shock and protect your burner. NET PRICED

Old Part# B01-001

Hi Amp Relay- 80 Continuous # 2039

View Larger Image

80 Amps Continuous, 300 Amp Spike Protection. Most 12 V burner problems are caused by the heavy in rush of power (spike). This condition can reduce the life of 12 Volt motors and Igniters by 80%. These relays will cushion the electrical shock and protect your burner. NET PRICED

Old Part# WR1-001

In-Line Adjustable Thermostat # 1426

View Larger Image

Install on the discharge side of the coil, Interchangeable with all in-line thermostats, Temperature range 60˚ F to 230˚ F.  PDF Breakdown.

NET PRICED

Panel Mount Thermostat- 194 Degree # 1425

View Larger Image

Adjustable to 194˚ F - Super Quick Response.  PDF Breakdown. NET PRICED

Old Part# 4510-100

Panel Mount Thermostat- 300 Degree # 1349

View Larger Image

Adjustable to 300˚ F, 7,000 PSI, 5˚ – 8˚  dead band - Super Quick Response. PDF Breakdown. NET PRICED

Old Part# 3560-101

Pre Set Thermostat-160 Degree # 1884

View Larger Image

On/Off at a Constant Temperature, 5˚ – 8˚ deadband - Super Quick Response, Shuts off at 160˚ F.  NET PRICED

Old Part# PST160

Pre Set Thermostat - 190 Degree # 1885

View Larger Image

On/Off at a Constant Temperature, 5˚ – 8˚ deadband - Super Quick Response, Shuts off at 190˚ F.  NET PRICED

Old Part# PST190

Hi-Limit Shut Down # 1107

View Larger Image

Shuts down the fuel solenoid at 210˚ F, Install on discharge side of coil, Wires in anywhere in-line with the burner controls prior to the fuel solenoid.  NET PRICED

Old Part# 1560-102

Pressure Switch- 3650PSI 1/4" MPT # 1370

View Larger Image

Rated for 250 Volts, 15 Amps, 190˚ F, 3,650 PSI, 1/4" MPT.  NET PRICED

Old Part# 4009-101

Pressure Switch- 3650PSI 3/8" MPT # 1371

View Larger Image

Rated for 250 Volts, 15 Amps, 190˚ F, 3,650 PSI, 3/8" MPT.  NET PRICED

Old Part# 4009-102

Pressure Switch- 6500PSI 1/4" MPT # 1372

View Larger Image

Rated for 250 Volts, 15 Amps, 190˚ F, 6,500 PSI, 1/4" MPT.  NET PRICED

Old Part# 4009-103

Flow Switch- Vertical Mount # 1367

View Larger Image

Tungsten Contact Reed Switch, Viton Seals, 4,400 PSI, For Solenoid Control Only. PDF Breakdown.  NET PRICED

Old Part# 4008-005

Flow Switch- Vertical or Horizontal # 1368

View Larger Image

Tungsten Contact Reed Switch, Viton Seals, 4,400 PSI, For Solenoid Control Only.  PDF Breakdown. NET PRICED

Old Part# 4008-006

Reedless Flow Switch # 1369

View Larger Image

No reed to replace, 5,000 PSI, 8 GPM, For controlling fuel solenoid only

PDF Breakdown  NET PRICED

Old Part# 4008-008

Phoenix Flow Switch #2272

View Larger Image

NET PRICED

Vac Switch- Gas Engine # 1373

Install on inlet side of pump, 1/4” FPT connector, Heavy duty 16 Amp connector, 140˚ F maximum water temperature. NET PRICED

Old Part# 4012-101

Vac Switch- Electric Motors # 1374

Install on inlet side of pump, 1/4” FPT connector, Heavy duty 16 Amp connector, 140˚ F maximum water temperature. NET PRICED

Old Part# 4012-102

On/Off Burner Switch # 1388

View Larger Image

Heavy Duty Toggle Switch, On/Off Positioning, Rated for 50 Amps at 12 Volts.  NET PRICED

Old Part# 4212-825

Circuit Breaker Fuses

View Larger Image

Resettable circuit breaker fuses for burners. Rated for 10, 15, and 30 amps. choose the appropriate size from the drop down list. NET PRICED

Old Part# CB10, CB15, CB30

Test Lights

Use these 12 volt led lights for a burner diagnosis system. It will tell you in 2 seconds what would normally take 2 hours to figure out. Use the simple enclosed instructions to wire up a complete burner diagnosis center on your machine in no time flat. Choose your lights from the drop down list.  NET PRICED

Test Switches Box- Switch Holder

View Larger Image

One and three gang switch box for holding burner test switches. Choose the appropriate size from the drop down list. Prices may vary based on model selected.  NET PRICED

Old Part# GB1, GB3

Burner Diagnostic Center - # 4001

View Larger Image

It never seems to fail. It is cold out and you really need heat. It is on the weekend when you are really backed up and on top of that all the pressure washer distributors are at home by the fire watching the Super Bowl. You stop at your first account after ‘psyching’ yourself that today is going to be an easy day and if you work really fast you might just catch the ‘tail end’ of the game.

AND THEN YOU PULL THE TRIGGER AND THE BURNER DOES NOT COME ON.

Typically when this happens it is at least a good hour or two, if you really know what you are doing, to diagnose the problem. A problem that when figured out generally takes only 5 minutes to fix. What if I told you that it only takes IT ONLY TAKES 2 SECONDS to figure out what is wrong or not wrong with your burner? Here is the “low cost’ solution that prevents ‘high cost’ down time!

THE ALLISON BURNER DIAGNOSTIC CENTER that ‘easily’ attaches to any hot water pressure washer.