Allison Engine Terminator # 1990

View Larger Image

When the water reaches 145˚ F engine is stopped saving you expensive pump repairs, for DC Current Only, Hooks up to pump inlet and senses bypass water temperature, Keep in mind that if you leave your pump in bypass for more than 3 Minutes the pump head has already reached 145˚ F. NET PRICED

Pump Thermal Protector- Plastic Barb # 1076

View Larger Image

Install on the inlet side of the pump. When bypass water reaches 145˚ F the valve opens and allows the heated water to escape. Only recommended for force fed pumps, if you are pulling from a tank we recommend the Allison Engine Terminator # TET-101.

1/2" mpt opens at 145 degrees. NET PRICED

Old Part# 1401-111

Pump Thermal Protector- Brass Barb # 1062

View Larger Image

Install on the inlet side of the pump. When bypass water reaches 145˚ F the valve opens and allows the heated water to escape. Only recommended for force fed pumps, if you are pulling from a tank we recommend the Allison Engine Terminator #TET-101.

3/8" mpt opens at 145 degrees.   PDF Breakdown  NET PRICED

Old Part# 1310-111

Easy Start Valve # 1124

View Larger Image

Installs on the high pressure (outlet) side of the pump and relieves the “back-pressure” during start-up

PDF Breakdown NET PRICED

Old Part# 1625-777

Safety Relief Valve # 1123

View Larger Image

Fully adjustable, Rated to 6,000 PSI, Up to 6 GPM, 195˚ F, Install on outlet side of pump prior to burner. NET PRICED

Old Part# 1610-600

Safety Relief Valve- With Barb # 1126

Fully adjustable, Rated to 6,000 PSI, Up to 6 GPM, 195˚ F, Install on outlet side of pump prior to burner.

PDF Breakdown NET PRICED

Old Part# 1710-601

Burst Disc # 1106

View Larger Image

Protect yourself in the event of burner failure, Pre set to open at 8,000 PSI.  NET PRICED

System Air Blow Out # 1074

View Larger Image

Place on inlet side of pump, Use air pressure to blow the water out of the system to prevent freezing. Install on low pressure side only. NET PRICED

Pump Antifreeze # 1768

View Larger Image

Protect your pump from freezing over the winter. Attaches to any pump inlet to fill the pump chamber with antifreeze solution. NET PRICED

Old Part# CQF01

General Pump Oil- 6 Pack # 1064

View Larger Image

It is reccommended to change your pump oil after the first 50 hours of operation, then every 3 months or as needed. Fill the oil half way up te sight glass indicator only do not over fill.

Not for use in engines.  PDF Breakdown         MSDS   NET PRICED

Old Part# 1310-800

General Pump Oil- 24 Pack # 1065

View Larger Image

It is reccommended to change your pump oil after the first 50 hours of operation, then every 3 months or as needed. Fill the oil half way up te sight glass indicator only do not over fill.

Not for use in engines.  PDF Breakdown           MSDS  NET PRICED

Old Part# 1310-801

BE Premium Oil- 1 Litre # 1066

View Larger Image

Ideal for high pressure pumps. Non detergent and non foaming. Specially formulated and rated for superior rust protection and oxidation protection.

It is reccommended to change your pump oil after the first 50 hours of operation, then every 3 months or as needed. Fill the oil half way up te sight glass indicator only do not over fill. Not for use in engines. NET PRICED

Old Part# 1310-805

Cat Pump Oil- 12 Pack # 4788

View Larger Image

It is reccommended to change your pump oil after the first 50 hours of operation, then every 3 months or as needed. Fill the oil half way up te sight glass indicator only do not over fill. Not for use in engines.  MSDS Sheet  NET PRICED